DEK 2-Way Feed Chipper/Shredder Manuel du propriétaire télécharger pdf (Page 21)

54Z, 62Z

Z- BEAST

BEAST Finish Mower

Rev: Mar2011

General Maintenance

The Importance of Maintenance

Regular maintenance is essential to ensure your

mower continues to deliver safe and high-quality

performance.

To help you properly care for your mower, the following

pages include a recommended maintenance schedule,

routine inspection procedures, and simple

maintenance procedures using basic hand tools.

Maintenance is the responsibility of the owner and

must be performed regularly. More difficult service

tasks or tasks that require special tools are best

handled by a recommended service technician or other

qualified mechanic.

The maintenance schedule described on page 14

applies to mowers used under normal operating

conditions. If you operate your mower under severe

conditions, such as sustained prolonged use or high-

temperature operations, or use it in unusually wet,

dusty or rocky conditions, consult your servicing dealer

for recommendations applicable to your individual

needs and use.

Be sure to use genuine Z- BEAST mower replacement

parts when servicing your mower to assure the best

quality, safety and performance.

Need Help? Parts, Service and Technical Assistance

Call: 1-919-550-3221 www.beastpowerequipment.com

CAUTION

CAUTION! Before making any adjustments and/or servicing to

your Z-BEAST mower, make sure the mower is on a level

surface, with the ignition switch off, the key removed, the brake

set, and the blades disengaged. Also, disconnect the spark plug

wires from the spark plugs and ground them against the engine

to prevent inadvertent starting.

If you are performing adjustments or maintenance after

operating the mower, allow the unit to cool and always wear

protective clothing.

Tire Pressure

Incorrect tire pressure may cause the mower to pull to one side

and/or result in uneven cut. Use caution when filling the tires.

NEVER exceed the recommended maximum tire pressure as

stated on the tires.

Air Filter

Refer to the Engine Owner’s Manual for the recommended

maintenance.

Engine Oil

CHECK ENGINE OIL BEFORE EACH USE. Refer to the Engine

Owner’s Manual for the type of oil to use, oil change intervals,

and the proper procedures to check and change oil.

Fuel

DANGER: Gasoline is highly flammable and

explosive. Do not add fuel while the engine is

running or is hot. Keep open flames, sparks, and

heat away from the fuel and store fuel in containers

specifically designed for that purpose. Add fuel

outdoors only and if the fuel is spilled, do not start

the engine. Manually push the mower away from the

spill and wipe up immediately.

Refer to the Engine Owner’s Manual for the type of fuel

to use.

A fuel shut off valve is located on the bottom of the fuel

tank. It is recommended that the fuel be shut off when

transporting between job sites and when storing the

mower for extended periods of time.

DANGER

CAUTION: Always wear work gloves when performing

blade maintenance and beware of the cutting edges.

Be sure the engine is off, the key removed, and the

spark plug wires are disconnected from the spark

plugs to prevent inadvertent starting.

CAUTION

Blades

Inspect blades on a daily basis for nicks, bends, and excessive

wear. If the blades are worn, cracked, bent, or damaged,

replace them before using the mower. Choose genuine Z-

BEAST mower replacement blades to ensure quality and

performance. (See page 16 for blade removal instructions.)

When sharpening the blades, sharpen only the cutting edges

and try to maintain the original angle of the blade. Do not make

the cutting edge razor sharp. Remove the same amount from

each side of the blade so that balance in maintained.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 30 31

Commentaires sur ces manuels

Pas de commentaire

DEK 2-Way Feed Chipper/Shredder Manuel du propriétaire Page 21

Commentaires sur ces manuels

Produits connexes et manuels pour Broyeurs pour jardin DEK 2-Way Feed Chipper/Shredder